/*-
* Copyright (c) 2010 , MWNL
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
* redistribution must be conditioned upon including a substantially
* similar Disclaimer requirement for further binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
* AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
* THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
* OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
* IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGES.
*
*/
/* Automatic rate fallback */
/*-------------------------INCLUDE FILES--------------------------------*/
#include <linux/config.h>
#include <linux/version.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/skbuff.h>
#include <linux/netdevice.h>
#include <linux/random.h>
#include <linux/delay.h>
#include <linux/cache.h>
#include <linux/sysctl.h>
#include <linux/proc_fs.h>
#include <linux/if_arp.h>
#include <linux/vmalloc.h>
#include <asm/uaccess.h>
#include <net80211/if_media.h>
#include <net80211/ieee80211_var.h>
#include "if_athrate.h"
#include "if_athvar.h"
#include "ah_desc.h"
#include "arf.h"
/*--------------------------------------------------------------------*/
#define ARF_DEBUG
#ifdef ARF_DEBUG
enum {
ATH_DEBUG_RATE = 0x00000010, /* rate control */
};
#define DPRINTF(sc, _fmt, ...) do { \
if (sc->sc_debug & ATH_DEBUG_RATE) \
printk(_fmt, __VA_ARGS__); \
} while (0)
#else
#define DPRINTF(sc, _fmt, ...)
#endif
/*--------------------------------------------------------------------*/
/*
* Default parameters for the rate control algorithm. These are
* all tunable with sysctls. The rate controller runs periodically
* (each ath_rateinterval ms) analyzing transmit statistics for each
* neighbor/station (when operating in station mode this is only the AP).
* If transmits look to be working well over a sampling period then
* it gives a "raise rate credit". If transmits look to not be working
* well than it deducts a credit. If the credits cross a threshold then
* the transmit rate is raised. Various error conditions force the
* the transmit rate to be dropped.
*
* The decision to issue/deduct a credit is based on the errors and
* retries accumulated over the sampling period. ath_rate_raise defines
* the percent of retransmits for which a credit is issued/deducted.
* ath_rate_raise_threshold defines the threshold on credits at which
* the transmit rate is increased.
*
* XXX this algorithm is flawed.
*/
/*---------STATIC VARIABLES---------------------------------------------------*/
static u_int8_t curr_bitrate = 0;
static u_int8_t old_bitrate = 0;
u_int8_t signal = 0;
//static int tries_0 = 0, tries_1 = 0, tries_2 = 0, tries_3 = 0;
//static int final_idx = 0;
/*------------------FUNCTION DECLARATION------------------------------*/
static void ath_rate_update(struct ath_softc *, struct ieee80211_node *, int);
static void ath_rate_ctl_start(struct ath_softc *, struct ieee80211_node *);
static void ath_rate_ctl(void *, struct ieee80211_node *);
//int get_rts_signal(void){return signal;};
void set_rts_signal(int data){signal = data;};
int get_rts_signal(void) {return signal;};
EXPORT_SYMBOL(get_rts_signal);
EXPORT_SYMBOL(set_rts_signal);
/*---------------------------------------------------------------------*/
/*-------------------FUNCTION DEFINATION------------------------------*/
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_node_init(struct ath_softc *sc, struct ath_node *an)
* DESCRIPTION: initialize the node
*---------------------------------------------------------------------*/
void
ath_rate_node_init(struct ath_softc *sc, struct ath_node *an)
{
/* NB: assumed to be zero'd by caller */
ath_rate_update(sc, &an->an_node, 0);
}
EXPORT_SYMBOL(ath_rate_node_init);
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_node_cleanup(struct ath_softc *sc, struct ath_node *an)
* DESCRIPTION: destroy information for a node
*---------------------------------------------------------------------*/
void
ath_rate_node_cleanup(struct ath_softc *sc, struct ath_node *an)
{
}
EXPORT_SYMBOL(ath_rate_node_cleanup);
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_findrate(struct ath_softc *sc, struct ath_node *an,
int shortPreamble, size_t frameLen,
u_int8_t *rix, int *try0, u_int8_t *txrate)
* DESCRIPTION: find bit rate for the current packet tx
*---------------------------------------------------------------------*/
void
ath_rate_findrate(struct ath_softc *sc, struct ath_node *an,
int shortPreamble, size_t frameLen,
u_int8_t *rix, int *try0, u_int8_t *txrate)
{
struct arf_node *on = ATH_NODE_ARF(an);
*rix = on->on_tx_rix0;
*try0 = 1; //no retransmissions configured
// *try0 = on->on_tx_try0;
if (shortPreamble)
*txrate = on->on_tx_rate0sp;
else
*txrate = on->on_tx_rate0;
DPRINTF(sc, "%s: \n", __func__);
}
EXPORT_SYMBOL(ath_rate_findrate);
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_setupxtxdesc(struct ath_softc *sc, struct ath_node *an,
struct ath_desc *ds, int shortPreamble, size_t frame_size, u_int8_t rix)
* DESCRIPTION: setup tx descriptor
*---------------------------------------------------------------------*/
void
ath_rate_setupxtxdesc(struct ath_softc *sc, struct ath_node *an,
struct ath_desc *ds, int shortPreamble, size_t frame_size, u_int8_t rix)
{
// struct arf_node *on = ATH_NODE_ARF(an);
ath_hal_setupxtxdesc(sc->sc_ah, ds
, 0,0 /*series 0*/
,0,0 /*series 1*/
,0,0 /*series 2*/
);
#if 0
// retransmission scheme off.
ath_hal_setupxtxdesc(sc->sc_ah, ds
, on->on_tx_rate1sp, 2 /* series 1 */
, on->on_tx_rate2sp, 2 /* series 2 */
, on->on_tx_rate3sp, 2 /* series 3 */
);
#endif
}
EXPORT_SYMBOL(ath_rate_setupxtxdesc);
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_tx_complete(struct ath_softc *sc,
struct ath_node *an, const struct ath_desc *ds)
* DESCRIPTION: post Tx handling (per packet basis)
Increment the bit rate if the tx_ok = 10(successive)
Decrement the bit rate if tx_err = 2 (successive)
*---------------------------------------------------------------------*/
void
ath_rate_tx_complete(struct ath_softc *sc,
struct ath_node *an, const struct ath_desc *ds)
{
struct arf_node *on = ATH_NODE_ARF(an);
#if 0
const struct ar5212_desc *ads = (const struct ar5212_desc *)&ds->ds_ctl0;
int rate0, tries0 ;
int rate1, tries1;
int rate2, tries2;
int rate3, tries3;
int finalTSIdx = ads->final_ts_index;
#endif
int final_rate = 0;
int short_tries = 0;
int long_tries = 0;
final_rate = (sc->sc_hwmap[ds->ds_txstat.ts_rate &~ HAL_TXSTAT_ALTRATE].ieeerate)/2;
short_tries = ds->ds_txstat.ts_shortretry + 1;
long_tries = ds->ds_txstat.ts_longretry + 1;
/*FOR DETERMINING THE AVERAGE TX RATE USED*/
msr.total_pkts++;
switch(final_rate)
{
case 54:
msr.p54_pkts++;
break;
case 48:
msr.p48_pkts++;
break;
case 36:
msr.p36_pkts++;
break;
case 24:
msr.p24_pkts++;
break;
case 18:
msr.p18_pkts++;
break;
case 12:
msr.p12_pkts++;
break;
case 9:
msr.p9_pkts++;
break;
case 6:
msr.p6_pkts++;
break;
default:
break;
}
if(ds->ds_txstat.ts_status == 0)
{
on->on_tx_ok++;
on->on_tx_err = 0;
}
else
{
on->on_tx_err++;
on->on_tx_ok = 0;
}
/*Increment the bit rate if the tx_ok = 10(successive) */
/* Decrement the bit rate if tx_err = 2 (successive) */
// signal = 0 ;
DPRINTF(sc, "%s: tx_ok=%d, tx_err = %d\n", __func__,on->on_tx_ok,on->on_tx_err);
set_rts_signal(signal); // this is presently not used
if(on->on_tx_ok == 10 || on->on_tx_err == 2)
ath_rate_ctl(sc, &an->an_node);
}
EXPORT_SYMBOL(ath_rate_tx_complete);
/*-----------------------------------------------------------------------*
* FUNCTION: ath_rate_newassoc(struct ath_softc *sc, struct ath_node *an, int isnew)
* DESCRIPTION: handle the new association
*---------------------------------------------------------------------*/
void
ath_rate_newassoc(struct ath_softc *sc, struct ath_node *an, int isnew)
{
if (isnew)
ath_rate_ctl_start(sc, &an->an_node);
}
EXPORT_SYMBOL(ath_rate_newassoc);
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_newassoc(struct ath_softc *sc, struct ath_node *an, int isnew)
* DESCRIPTION: handle the new association
*---------------------------------------------------------------------*/
static void
ath_rate_update(struct ath_softc *sc, struct ieee80211_node *ni, int rate)
{
struct ath_node *an = ATH_NODE(ni);
struct arf_node *on = ATH_NODE_ARF(an);
const HAL_RATE_TABLE *rt = sc->sc_currates;
u_int8_t rix;
KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
DPRINTF(sc, "%s: set xmit rate for %s to %dM\n",
__func__, ether_sprintf(ni->ni_macaddr),
ni->ni_rates.rs_nrates > 0 ?
(ni->ni_rates.rs_rates[rate] & IEEE80211_RATE_VAL) / 2 : 0);
ni->ni_txrate = rate;
/*
* Before associating a node has no rate set setup
* so we can't calculate any transmit codes to use.
* This is ok since we should never be sending anything
* but management frames and those always go at the
* lowest hardware rate.
*/
if (ni->ni_rates.rs_nrates == 0)
goto done;
on->on_tx_rix0 = sc->sc_rixmap[ni->ni_rates.rs_rates[rate] & IEEE80211_RATE_VAL];
on->on_tx_rate0 = rt->info[on->on_tx_rix0].rateCode;
on->on_tx_rate0sp = on->on_tx_rate0 |
rt->info[on->on_tx_rix0].shortPreamble;
if (sc->sc_mrretry) {
/*
* Hardware supports multi-rate retry; setup two
* step-down retry rates and make the lowest rate
* be the ``last chance''. We use 4, 2, 2, 2 tries
* respectively (4 is set here, the rest are fixed
* in the xmit routine).
*/
on->on_tx_try0 = 1; /*right now 1 as no retr handled, 4 tries at rate 0 */
if (--rate >= 0) {
rix = sc->sc_rixmap[ni->ni_rates.rs_rates[rate]&IEEE80211_RATE_VAL];
on->on_tx_rate1 = rt->info[rix].rateCode;
on->on_tx_rate1sp = on->on_tx_rate1 |
rt->info[rix].shortPreamble;
} else
on->on_tx_rate1 = on->on_tx_rate1sp = 0;
if (--rate >= 0) {
rix = sc->sc_rixmap[ni->ni_rates.rs_rates[rate]&IEEE80211_RATE_VAL];
on->on_tx_rate2 = rt->info[rix].rateCode;
on->on_tx_rate2sp = on->on_tx_rate2 |
rt->info[rix].shortPreamble;
} else
on->on_tx_rate2 = on->on_tx_rate2sp = 0;
if (rate > 0) {
/* NB: only do this if we didn't already do it above */
on->on_tx_rate3 = rt->info[0].rateCode;
on->on_tx_rate3sp =
on->on_tx_rate3 | rt->info[0].shortPreamble;
} else
on->on_tx_rate3 = on->on_tx_rate3sp = 0;
} else {
on->on_tx_try0 = 1; //ATH_TXMAXTRY; /* max tries at rate 0 */
on->on_tx_rate1 = on->on_tx_rate1sp = 0;
on->on_tx_rate2 = on->on_tx_rate2sp = 0;
on->on_tx_rate3 = on->on_tx_rate3sp = 0;
}
done:
on->on_tx_ok = on->on_tx_err = on->on_tx_retr = on->on_tx_upper = 0;
}
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_ctl_start(struct ath_softc *sc, struct ieee80211_node *ni)
* DESCRIPTION: Set the starting transmit rate for a node.
*---------------------------------------------------------------------*/
static void
ath_rate_ctl_start(struct ath_softc *sc, struct ieee80211_node *ni)
{
#define RATE(_ix) (ni->ni_rates.rs_rates[(_ix)] & IEEE80211_RATE_VAL)
struct ieee80211vap *vap = ni->ni_vap;
int srate;
KASSERT(ni->ni_rates.rs_nrates > 0, ("no rates"));
if (vap->iv_fixed_rate == IEEE80211_FIXED_RATE_NONE) {
/*
* No fixed rate is requested. For 11b start with
* the highest negotiated rate; otherwise, for 11g
* and 11a, we start "in the middle" at 24Mb or 36Mb.
*/
srate = ni->ni_rates.rs_nrates - 1;
if (sc->sc_curmode != IEEE80211_MODE_11B) {
/*
* Scan the negotiated rate set to find the
* closest rate.
*/
/* NB: the rate set is assumed sorted */
/*PROBABLY CHANGE 72 TO 108 FOR STARTING WITH 54M */
for (; srate >= 0 && RATE(srate) > 108; srate--);
KASSERT(srate >= 0, ("bogus rate set"));
}
} else {
/*
* A fixed rate is to be used; iv_fixed_rate is the
* 802.11 rate code. Convert this to the index into
* the negotiated rate set for the node. We know the
* rate is there because the rate set is checked when
* the station associates.
*/
/* NB: the rate set is assumed sorted */
srate = ni->ni_rates.rs_nrates - 1;
for (; srate >= 0 && RATE(srate) != vap->iv_fixed_rate; srate--);
KASSERT(srate >= 0,
("fixed rate %d not in rate set", vap->iv_fixed_rate));
}
ath_rate_update(sc, ni, srate);
#undef RATE
}
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_cb(void *arg, struct ieee80211_node *ni)
* DESCRIPTION: callback function for rate update
*---------------------------------------------------------------------*/
static void
ath_rate_cb(void *arg, struct ieee80211_node *ni)
{
ath_rate_update(ni->ni_ic->ic_dev->priv, ni, (long) arg);
}
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_newstate(struct ieee80211vap *vap, enum ieee80211_state state)
* DESCRIPTION: Reset the rate control state for each 802.11 state transition.
*---------------------------------------------------------------------*/
void
ath_rate_newstate(struct ieee80211vap *vap, enum ieee80211_state state)
{
struct ieee80211com *ic = vap->iv_ic;
struct ath_softc *sc = ic->ic_dev->priv;
struct ieee80211_node *ni;
if (state == IEEE80211_S_INIT)
return;
if (vap->iv_opmode == IEEE80211_M_STA) {
/*
* Reset local xmit state; this is really only
* meaningful when operating in station mode.
*/
ni = vap->iv_bss;
if (state == IEEE80211_S_RUN) {
ath_rate_ctl_start(sc, ni);
} else {
ath_rate_update(sc, ni, 0);
}
} else {
/*
* When operating as a station the node table holds
* the AP's that were discovered during scanning.
* For any other operating mode we want to reset the
* tx rate state of each node.
*/
ieee80211_iterate_nodes(&ic->ic_sta, ath_rate_cb, NULL);
ath_rate_update(sc, vap->iv_bss, 0);
}
}
EXPORT_SYMBOL(ath_rate_newstate);
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_ctl(void *arg, struct ieee80211_node *ni)
* DESCRIPTION: Examine and potentially adjust the transmit rate.
*---------------------------------------------------------------------*/
static void
ath_rate_ctl(void *arg, struct ieee80211_node *ni)
{
struct ath_softc *sc = arg;
struct arf_node *on = ATH_NODE_ARF(ATH_NODE(ni));
struct ieee80211_rateset *rs = &ni->ni_rates;
int dir = 0, nrate;
sc->sc_stats.ast_rate_calls++;
if(on->on_tx_ok == 10)
dir = 1; /*increase bit rate*/
if(on->on_tx_err == 2)
dir = -1; /*decrease bit rate*/
nrate = ni->ni_txrate; /*Current bit rate*/
switch(dir)
{
case 0:
{
/*maintain the same bit rate*/
break;
}
case -1:
{
/*decrement the bit rate by one index*/
if (nrate > 0)
{
nrate--;
sc->sc_stats.ast_rate_drop++;
}
break;
}
case 1:
{
/*Increment the bit rate by one index*/
if (nrate + 1 < rs->rs_nrates)
{
nrate++;
sc->sc_stats.ast_rate_raise++;
}
break;
}
default:
break;
}
DPRINTF(sc, "%s: ok %d err %d retr %d upper %d dir %d\n",
ether_sprintf(ni->ni_macaddr),
on->on_tx_ok, on->on_tx_err, on->on_tx_retr,
on->on_tx_upper, dir);
if (nrate != ni->ni_txrate) {
DPRINTF(sc, "%s: %dM -> %dM (%d ok, %d err, %d retr)\n",
__func__,
(rs->rs_rates[ni->ni_txrate] & IEEE80211_RATE_VAL) / 2,
(rs->rs_rates[nrate] & IEEE80211_RATE_VAL) / 2,
on->on_tx_ok, on->on_tx_err, on->on_tx_retr);
ath_rate_update(sc, ni, nrate);
}
curr_bitrate = (rs->rs_rates[nrate] & IEEE80211_RATE_VAL) / 2;
old_bitrate = (rs->rs_rates[ni->ni_txrate & IEEE80211_RATE_VAL])/2;
/*-reset the parameters-*/
on->on_tx_ok = 0;
on->on_tx_err = 0;
on->on_tx_retr = 0;
on->on_tx_upper = 0;
}
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_attach(struct ath_softc *sc)
* DESCRIPTION:
*---------------------------------------------------------------------*/
struct ath_ratectrl *
ath_rate_attach(struct ath_softc *sc)
{
struct arf_softc *osc;
osc = kmalloc(sizeof(struct arf_softc), GFP_ATOMIC);
if (osc == NULL)
return NULL;
osc->arc.arc_space = sizeof(struct arf_node);
osc->arc.arc_vap_space = 0;
return &osc->arc;
}
EXPORT_SYMBOL(ath_rate_attach);
/*---------------------------------------------------------------------*
* FUNCTION: ath_rate_detach(struct ath_ratectrl *arc)
* DESCRIPTION:
*---------------------------------------------------------------------*/
void
ath_rate_detach(struct ath_ratectrl *arc)
{
struct onoe_softc *osc = (struct onoe_softc *) arc;
kfree(osc);
}
EXPORT_SYMBOL(ath_rate_detach);
/*---------------------------PROC FILE SYSTEM--------------------------*/
#ifdef CONFIG_SYSCTL
static int
proc_read_nodes(struct ieee80211vap *vap, char *buf, int space)
{
char *p = buf;
// p += sprintf(p, "curr_rate %3d\t Old_rate %3d\t tries_0 %3d\t tries_1 %3d\t tries_2 %3d\t tries_3 %3d\t finaltxind %3d\n",curr_bitrate,old_bitrate,tries_0,tries_1,tries_2,tries_3,final_idx);
p += sprintf(p ,"total_pkts\t54_pkts\t48_pkts\t36_pkts\t24_pkts\t18_pkts\t12_pkts\t9_pkts\t6_pkts\n");
p += sprintf(p, "%3d\t%3d\t%3d\t%3d\t%3d\t%3d\t%3d\t%3d\t%3d\n",
msr.total_pkts,msr.p54_pkts,msr.p48_pkts, msr.p36_pkts,
msr.p24_pkts, msr.p18_pkts, msr.p12_pkts,
msr.p9_pkts,msr.p6_pkts);
return (p - buf);
}
int
proc_ratearf_open(struct inode *inode, struct file *file)
{
struct proc_ieee80211_priv *pv = NULL;
struct proc_dir_entry *dp = PDE(inode);
struct ieee80211vap *vap = dp->data;
if (!(file->private_data = kmalloc(sizeof(struct proc_ieee80211_priv),
GFP_KERNEL)))
return -ENOMEM;
/* intially allocate both read and write buffers */
pv = (struct proc_ieee80211_priv *) file->private_data;
memset(pv, 0, sizeof(struct proc_ieee80211_priv));
pv->rbuf = vmalloc(MAX_PROC_IEEE80211_SIZE);
if (!pv->rbuf) {
kfree(pv);
return -ENOMEM;
}
pv->wbuf = vmalloc(MAX_PROC_IEEE80211_SIZE);
if (!pv->wbuf) {
vfree(pv->rbuf);
kfree(pv);
return -ENOMEM;
}
memset(pv->wbuf, 0, MAX_PROC_IEEE80211_SIZE);
memset(pv->rbuf, 0, MAX_PROC_IEEE80211_SIZE);
pv->max_wlen = MAX_PROC_IEEE80211_SIZE;
pv->max_rlen = MAX_PROC_IEEE80211_SIZE;
/* now read the data into the buffer */
pv->rlen = proc_read_nodes(vap, pv->rbuf, MAX_PROC_IEEE80211_SIZE);
return 0;
}
static struct file_operations proc_ratearf_ops = {
.read = NULL,
.write = NULL,
.open = proc_ratearf_open,
.release = NULL,
};
void
ath_rate_dynamic_proc_register(struct ieee80211vap *vap)
{
/* Create proc entries for the rate control algorithm */
ieee80211_proc_vcreate(vap, &proc_ratearf_ops, "ratestats");
}
EXPORT_SYMBOL(ath_rate_dynamic_proc_register);
#endif /* CONFIG_SYSCTL */
/*------------------------MODULE DESCRIPTION-----------------------------*/
//static struct ctl_table_header *ath_sysctl_header;
#include "release.h"
static char *version = "1.0 (" RELEASE_VERSION ")";
static char *dev_info = "ath_rate_arf";
MODULE_AUTHOR("MWNL, Lochan Verma");
MODULE_DESCRIPTION("Automatic ratefallback algorithm for Atheros devices");
#ifdef MODULE_VERSION
MODULE_VERSION(RELEASE_VERSION);
#endif
#ifdef MODULE_LICENSE
MODULE_LICENSE("Dual BSD/GPL");
static int __init
init_ath_rate_arf(void)
{
printk(KERN_INFO "%s: %s\n", dev_info, version);
#if 0
#ifdef CONFIG_SYSCTL
ath_sysctl_header = register_sysctl_table(ath_root_table, 1);
#endif
#endif
return (0);
}
module_init(init_ath_rate_arf);
static void __exit
exit_ath_rate_arf(void)
{
#if 0
#ifdef CONFIG_SYSCTL
if (ath_sysctl_header != NULL)
unregister_sysctl_table(ath_sysctl_header);
#endif
#endif
printk(KERN_INFO "%s: unloaded\n", dev_info);
}
module_exit(exit_ath_rate_arf);
#endif
